When the incoming stones pile up behind the opening of the machine, usually the first reaction is that the crusher does not have enough capacity. But the problem may lie elsewhere: the feed size does not read with the inlet opening, the feed is not uniform, or worn jaws no longer produce the expected output. For the technical officer or parts buyer in Tehran, the difference between these reasons is important; Because each one has a different decision and cost. Jaw crusher for mining should be evaluated along with the feed, downstream equipment and consumables condition, not just by model name or catalog capacity number.
When is a jaw crusher the right choice for mining?
A jaw crusher is usually suitable for primary grinding; That is, the place where the large pieces of rock should reach enough for the next equipment in the line to process them. Its correct selection depends on the size and material of the feed, the required capacity of the line and the acceptable output size, not on the device being bigger alone.
In this device, the stone between the fixed jaw and the movable jaw is crushed under pressure. A material that has been shrunk enough is ejected from the bottom of the chamber; Therefore, the opening of the inlet, the shape of the chamber and the adjustment of the outlet all have an effect on the performance.
Before comparing the models, several questions should be answered: What are the dimensions of the largest piece of feed? How much material per hour actually reaches the crusher? Is the output product going to go into a sander, a secondary crusher, or another part of processing? The answer to these questions determines what the jaw device should do and what should not be expected from it.
For example, if the goal is to produce final aggregates of sand, the choice of jaw crusher is only part of the decision. The performance of the sand and the subsequent stages of crushing should also be considered. For this reason, comparing sand crusher price without specifying the capacity of the entire line, the type of feed and the desired product, does not give an accurate picture of the cost of the project.
What variables change the jaw crusher performance?
Three variables should be considered together: Input feed, outlet adjustment and condition of wear parts. Changing each can change the practical capacity, product granularity and number of line stops; Even if the device model remains the same.
Size and consistency of incoming feed
The coarsest input stone should be compatible with the opening and working range of the same machine model. Irregular feeding or the entry of disproportionate parts can disrupt the passage of material through the chamber; So the nominal capacity should not be considered equivalent to continuous production in the real conditions of the mine.
Don't just take a photo of the biggest rock to evaluate the feed. Record the share of coarse stones, the amount of fine grains, feed changes between shifts and how the material enters the feeder. If the problem only occurs when certain loads arrive, it may make more sense to modify the feeding method or control the size of incoming stones than to replace the machine.
Also, the bottleneck after the stone crusher should be known. If the conveyor belt or conveyor is not capable of receiving the output, increasing the capacity of the primary machine does not necessarily increase the production of the entire line. The decision criterion is the usable output tonnage of the entire line, not just the amount of material entering the jaw.
The outlet opening and the position of the jaws
Exit closed opening or CSS is the minimum distance between two jaws in the exit part of the movement cycle. Adjusting it affects the size of the product, but reducing the aperture alone is not a better production solution and should be considered together with the capacity and needs of the next step. Experimental research on jaw crusher parameters also shows that the effect of CSS on product and performance is dependent on the purpose of granulation and test conditions.
Fixed jaw and movable jaw are parts that should be checked regularly for wear. When buying crusher parts, the apparent size or title of the alloy is not enough to make a decision; It is also important to match the part with the machine model, the shape of the cutting surface, the installation location and the feed conditions. For example, a research on the wear of manganese steels in the jaw crusher test showed that the wear behavior of fixed and mobile jaws is not the same, and more manganese does not necessarily mean a more economical choice in all situations.
Variable | What to check? | Common error | Criteria Better decision |
Input feed | Coarse stone size, fines and feed uniformity | Select machine based on average stone size only | Registration of feed samples in several shifts |
Capacity | Required production of the entire line and power of the next equipment | Knowing the capacity of the catalog with the production true | Useable line output measurement |
Output span | CSS and granularity required next step | Close Over-opening to make the product smaller | Setting based on the performance of the whole circuit |
Jaws and wear parts | Model, installation dimensions, jaw shape and wear pattern | Purchasing parts only based on price or alloy name | Adjusting specifications and calculating cost per operation |
Maintenance | Downtime, failure reason and parts inventory Necessary | Part replacement without checking the cause of wear | Recording and correcting the cause of repeated failure |
I, Javad Rajabi, in reviewing the selection of jaw crusher parts, I do not start the conversation with the name of the part; First, I ask how the previous piece is worn. The difference between uniform wear, one-sided wear, and repetitive failure can be a clue to check the power supply, installation, or adjustment of the device, not just a reason to reorder the same part.
For buyers who follow the supply of parts from Tehran, a costly mistake is to delay the purchase until the machine is completely stopped. At that moment, the opportunity to accurately match the part specifications, investigate the cause of the failure and plan the replacement is reduced. The real cost of the piece is not just the invoice amount; The sleep time of the line and the possibility of repeating the same failure are also part of the decision.
A tip I recommend to colleagues is to prepare a "short machine file": model and identification number, picture of installation location, dimensions or drawing of part, date of previous replacement, approximate tonnage processed and photo of worn surface. This information will help avoid confusing similarly named parts with truly compatible parts when talking to a crushing equipment dealer. Of course, photographs and field measurements do not replace the manufacturer's drawing and technical approval of the part.
Safety should not be postponed until the end of the repair program. Rock jamming in the chamber isn't just a matter of stopping production: even after a shutdown, there's a risk of parts suddenly moving or releasing stored energy. The accident investigation report of the US Mine Safety and Health Administration, MSHA, has recorded the same danger in clearing jaw crusher jams; Before any intervention, the safe method specific to the device must be implemented by trained people.
A road map for choosing a device and buying parts
The less error-prone path is to first define the stone crusher's task in the line, then measure the specifications of the machine and parts with the same task. If the device is available, before purchasing the part or deciding to replace it, check the cause of the performance loss from the operation data and safe visit.
- Specify the task of the first step. Record the size of the input feed, the required capacity and the desired output size for the next step in a sheet. "Producing more" is not a sufficient goal; It should be clear which section of the line requires which outlet.
- Collect actual feed data. Sample typical loads and problem loads and record changes in rock size and material. Choosing based on an exceptional load or a low load day can both be misleading.
- Check the current machine condition apart from the nominal capacity. Evaluate the outlet setting, feed uniformity, jaw condition and discharge path according to the same machine manual. Inspection should be done with proper stopping and securing; Tampering with housing during operation is not a means of troubleshooting.
- For replacement part, document conformance. Provide device model, drawing or technical code, seat dimensions and joint location along with photo of previous part. In Sazakh Sazeh Company, the basis of technical discussion about the sale of mining jaw crusher parts should be the same verifiable specifications, not the similarity of the names of the parts.
- Connect the cost to the performance. When comparing the options, put the purchase price in addition to the observed durability, replacement time and the effect of line stoppage. Without recording the feed conditions and performance, it is usually not fair to compare the life of two parts.
- See the safety and dust control program at the same time. Material entry and discharge points can be a source of dust; Depending on the line design and material, controls such as containment, local ventilation, or appropriate dust containment methods should be considered. The NIOSH guide emphasizes the evaluation of these points in the crushing operation.
Conclusion and final opinion
In my opinion, jaw crusher for mining is a successful choice when we see the device, feed and consumables as a set. Nominal capacity is the starting point of comparison; The final decision should be made based on the required output of the line, the compatibility of the parts, the history of stops and the possibility of safe maintenance.
If you are in doubt between repairing the existing machine, changing the settings or choosing a replacement part, put together the specifications of the feed, the model of the machine and the pictures of the worn parts. This brief case makes the discussion between me and my colleagues at Crusher Construction Company more precise and helps to investigate the real issue of the line instead of a hasty answer.
تماس با ما


