Introduction
chain typur (or handheld or chain tapor) is a tool for lifting or pulling heavy loads. The chain typhoor repair needs to know the internal parts and how it works. The following is a general process for repairing this device:
General Steps for Chain Typhore Repair:
1. Initial review and troubleshooting
-Make the tie that the typho is not stuck in the work. -Check the function of the hooks, the lever handle, the brake system, and the chains. -If the chains are stuck, torn, or does not move, it may be a problem with internal ribs or springs.
2. Open the device frame
-Carefully open the typical screws and place the pieces on a clean surface. -In Note that the internal spring may be under pressure -opening it requires caution.
3. Examine the internal parts
-Wheels: They should be fractured and corrosion. -Brake System (clutch): Make sure the brake plates are healthy. -Finers: Replace broken or loose springs. -Amier: Replace in case of corrosion or fracture.
4. Cleaning and lubricating
-Use special grease for gear lubrication. -Lubricate with a special lubricant oil.
5. Replace the broken parts
-Use the original spare parts. -No -Installation of new parts must be in accordance with the factory order.
6. Close Typhor again
-Close all the pieces in place. -Coprate the screws tightly and with the correct order.
7. Performance test
-Try the typhoor without load. -In consult the chains easily and opened the brake system correctly.
Safety Tips:
-Always use safety gloves and protective glasses. -Do not try the Tifur at all under its capacity. -اگر آسیب جدی یا شکستگی در قطعات اصلی مشاهده شد، بهتر است دستگاه را تعویض یا به یک تعمیرکار حرفهای واگذار کنید.
Complete Tyfore Chain Repair Guide
The main components of the chain typhoor
1. Metal body - protective parts of the interior 2. Manual lever (Liver) - to move the chains 3. Gear Set - Power Transfer 4. Brake system (Brake Disc & Ratchet Mechanism) - Loading 5. Load Chain (Load Chain) - to lift or pull the load 6. Hook up and down (Hooks) - Loading and Relo 7.
The common problems of the chain typhoture
-stuck in rust, damaged gear and lubrication, gear shift -The revolution does not open the spring or the thorns of the hook. -For does not hold the load failure or the wheels are eaten. -Ra does not move the gear is stuck or broken is opening and checking the force transfer mechanism -Unusual lubrication or fracture of lubrication internal parts, replacement of broken pieces
The tool needed to repair
-French wrench or set -Two -and -four -Break and Barbecue -Industrial or wheeled oil -Safety and protective glasses -Spare and consumables (if needed)
Steps to Step to Chain Typore Repair
1. Preparation and safety -Remove the typhoor from the load and place in a clean environment. -This thoroughly pull out of the body.
1. Open the device -Open the body screws (note that the internal spring may be released). -Conies the seals on a surface to keep their arrangement.
1. Internal parts check Check the disc brake, it should not be eroded or oil. Check the ribs for lipstick or fracture. Check the chains in terms of swing, cracking or fracture. Test the lever that easily involves the wheels.
1. Cleaning and psychoanalysis -Use a special bearings or wheels. -Clean with a brush and then lubricate. -Do not oil the brake because it causes slip.
1. Replace the broken parts -Replace if a piece (such as brake pads or lever spring) replace it. -Spare points must be in accordance with the brand and model. 1. Assemble re -assembly -Carefully close all the pieces in place. -Make sure the screws are stiff.
7. Final experiment -No load, rotate the lever and make sure the chains go up and down. -Test the revolutions. -This Take the Final Test Style.
Professional Tips for Repairers
-Always periodically serve the typor every 6 months. -If the typor is used outdoors or humid, increase the frequency of lubrication. -Do not use the "vertical freight for" for horizontal pulling will cause faster failure. -Higher capacity -poweredfires (eg 3 tons up) usually have a more sophisticated brake system; In these cases, if you have no experience, give the repair to the specialist.
