Why is the correct replacement of the filters so vital?

Filter Oil Filter: Prevents the entry of fractures and combustion particles into the motor.
Hydraulic Filter: Protects the most sensitive system from contaminants that can prevent pumps, lions and jacks. (Dustus): removes solid particles from fuel and protects the injector and fuel pump system.
Air Filter: Prevents the dust from entering the abrasive combustion chamber. Has.

10 Deadly Mistakes in Switching Heavy Machinery Filters

Mistake 1: Use cheap and poor quality filters

Why is it dangerous? counterfeit and poor quality filters are made of inferior filtration materials with large pores that are not capable of absorbing fine particles. Poor adhesives and inappropriate seams in their structure cause the oil or fuel to pass through the filter media without filtering. This means that there is virtually no filter in the circuit!
Television Solution: In Television , we emphasize the critical importance of the filter quality. We only offer original filters or from reputable OEM and Alfary brands (such as FleetGuard, Donaldson, Baldwin) that meet the standard of machinery manufacturers. Investing in a high -quality filter from TechnoSpace is the best insurance for your machine's expensive components.

Mistake 2: Failure to Clean the Filter Installation Location

Why are it dangerous? Dust, old grease and stacked particles on the filter base easily enter the oil or fuel ducts when installing a new filter. This volume of centralized contamination can cause serious damage to the system at the first moment.
Correct solution: Always clean it with a clean, lint or wind pressure (cautiously) before opening the old filter. The surface of the filter seat on the engine or hydraulic base should be completely shiny and free of any contamination.

Mistake 3: Fill the new filter with oil or dirty gasoline

Why is it dangerous? The oil that is poured from an open gallon or dirty container inserts the contamination particles directly to the clean filter (that is, the side that goes to the engine). These contaminants enter the engine or refueling system at the first starter without any obstacles.
The correct solution: Always use a completely clean and closed container to fill the filter. The best way is to pour fuel or oil from the smaller ducts around the edge of the filter, not in the center hole. This will allow the fluid first to pass through the filtration media and then enter the clean section. Many makers even recommend that the filter be installed empty and ventilates through manual pumps.

Mistake 4: Gasket Filter Gasket

Why is it dangerous? Dry gaskets do not slice properly on the surface when tightening the filter and may have a torsion, rupture or collecting. This defect in sealing results in oil or fuel leakage, which in addition to dirty, can cause oil pressure and motor damage.
correct solution: Always before installing, a thin layer of clean oil (or clean grease in specific cases) with finger on the surface. This will make the filter tightened softly and completely sealing.

Mistake 5: Tightening too much or less than filter

"The tighter, the better!" This is a misconception. Both over -tightening and loosening the filter is a problem.

Why is it dangerous?
- Tightening too much: Crushes, thread damage and even cracked the filter shell. Opening such a filter in the next service will also be a nightmare.
- Tightening less than: due to motor shakes, the filter will gradually relax and cause severe and sudden leakage of oil or fuel that can lead to complete failure of the device. Is the filter. Usually the instructions are: "After contact with the surface, tighten the filter as much as 3/43/43/41 to 111." Using a filter wrench is recommended only to open the old filter, not to close the new filter (except in specific cases that require cracks).

Mistake 6: Use inappropriate tools

Trying to open a firm filter with a screwdriver and hammer is a familiar but very wrong scene.

Why is it dangerous? Picing with a screwdriver can cause metal scraps into the base of the filter. It is also dangerous and can damage the operator or the surrounding parts.
Solid solution: Always use the appropriate filter wrench (chain, belt or bowl). These tools are designed to do the same and do the right thing without damaging the parts.

Mistake 7: Ignoring the timing plans of replacement

"Still early, the device works well!" This sentence is an introduction to many costly failures. Delay Switching heavy machinery filters is not a savings, but a risky gamble.

Why is it dangerous? The filter is saturated after a while and its pores are blocked. This increases the pressure in the system and the bypass valve opens inside the filter to prevent the shell from bursting. With the opening of this valve, the dirty and filtered fuel or fuel will be directly logged in. These tables are adjusted based on the device's operation. In very lively work environments, it is best to shorten the filter replacement intervals (especially the air filter).

Mistake 8: Failure to check old filter

Old filter after opening is a valuable source of information about the health of your device. Flogging it without examination takes you an important diagnostic opportunity.

Why is it dangerous? You ignore the basic symptoms of a big problem.
Correct solution: After opening the oil filter, cut it with special tools and check the paper media inside it. The presence of glossy metal clashes (signs of bearings), overdose black particles (symptom of combustion) or other abnormal contaminants is a serious alarm that allows you to prevent preventive action before the catastrophe.

Mistake 9: Failure to properly air system

After Fuel Filter Replacement , air entry into the system is a natural thing. If this air is not drained properly, the device will not turn on or work by raying.

Why is it dangerous? Repeated effort to start with air in the system, pushing the fuel pump and the injector system and emptying the battery.
Correct solution: use a pump pump on the filter. Slightly loose the vent screw and pump until pure gasoline without bubble. Then tighten the screw.

Mistake 10: Not registering date and time of operation

forgetfulness is the number one enemy of regular maintenance. How can you plan for the next service if you don't know when you first replaced the filter?

Why is it dangerous? This results in breach of service schedule and misconception # 7
Solution: always after replacement of heavy machinery filters with an anti -water magic, date and date. This simple task is a great reminder for future services.

TechnoPart: Your partner in the maintenance of machinery

Avoid these 10 mistakes, the first and most important step to extend the life and efficiency of your machinery. The second step is to access quality and standard parts and filters. Television as a specialized center for supplying road parts in Rasht and Gilan, covering this vital need.

We provide:

Complete Filter Collection: For all kinds of Komatsu, Hyundai, Caterpillar, Dusan and…
Guaranteed Originality and Quality: Our Original Filters and Brands. Guide for your device and working conditions.
Competitive Price: Provide the best quality at the most appropriate price.

help you convert the process of replacement of heavy machinery filters into a clever investment to maintain the health of your device. With a call TechnoPart , get the technical knowledge of our experts and provide your required filters with full confidence. Do not let small mistakes turn into great damage.